Asm1062 serial ata controller driver how to#
Asm1062 serial ata controller driver install#

Product: RTL8169 PCI Gigabit Ethernet ControllerĬapabilities: bus_master rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiationĬonfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s Product: RTL8111/8168/8411 PCI Express Gigabit Ethernet ControllerĬapabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiationĬonfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.145 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s It must be something else about the configuration that is causing issues but I have no idea what. Ran the install, did the reboot and can't find it again. Diskstation was found and recognised as not installed. So I tried 1.03b loader and DSM 6.2 23739.pat on a spare single hard drive with all the other drives disconnected. It seems other people are able to 'upgrade', 'migrate' or 'recover' their data, I'm not sure why I can't? It seems something about the existing data is causing issues with DHCP or something, but I can't find a way to 'install from scratch' within the web manager initial setup so I think I will need to either format the volume and separate the drives or delete all files/folders from the volume that aren't specifically shares I've created. *EDIT* Interestingly when I login to my router I don't see the NAS as a connected device, and yet I was able to see it there the first time and when I booted to reinstall on the newer loader. I used mdadm and lvm to mount the drives to check for the xpenoboot folder.

Asm1062 serial ata controller driver how to#

I do have a copy of the data from the NAS so I will try to format the drives and run it again, but I'm not sure how to remove the drives from the RAID volume inside Linux. So I'm not really sure what to do at this point. Rebooted the NAS and chose Baremetal Reinstall and same issue - can't find the diskstation on the LAN. I chose repair, waited for it to complete and reboot, then had the same issue of diskstation not found on the LAN. I went to and found the diskstation, it said that it recognised a DSM from a previous system and needed to repair the system. I then setup Jun Loader 1.02b on the USB following the tutorial here. So I booted to Linux and mounted the RAID volume but couldn't find an xpenoboot or. Try booting from a live Ubuntu USB stick. I will try to format the drives (data is backed up) and try to set everything up with 6.1 if I can't find a solution, but thought I'd check here and see if I'm missing something before I give up. Every time I choose the baremetal reinstall option I can find the DS on the LAN, but after installation and reboot it goes missing again. I chose reinstall, went through the process and reboot - unable to find DS on LAN again.

Asm1062 serial ata controller driver install#

I chose baremetal reinstall option and the DSM is found with the option to migrate or clean install again. I then rebooted again with the same issue. I first tried to migrate and it went through the process then rebooted but was unable to find the DS on the LAN. I am able to boot from USB, go to and it recognises the DSM with data from a previous DSM and tells me I can migrate or do a clean install. My hardware is below:Īdditional Marvell 88SE63xx/64xx PCI-e SATA cardĪdditional TP-Link TG-3269 PCI Ethernet card I am using Jun's DSM 6.2 loader and trying to load DS3615XS_15284.PAT file. I've just moved from a working 5.2 Xpenology to different hardware and trying to get 6.2 installed.